Jewel 2, a new collection of shimmering and glittering textured vinyl from AS Creation, incorporating many loved patterns re-imagined and new designs for your walls.
Geo Shimmer is a new design to our collections, its uses a striking mix of new textures, finishes and a two-tone colour effect to establish itself. Based on a hessian weave relief texture, the geometric pattern is sunken and surrounded by a beige tactile texture that has been treated to a generous layer of gold glitter that rests on the peaks of the texture.
The matrix of trellis work has been given a duo of finishes either a smooth soft sheen finish with linear engraving in rose gold and a clean hessian relief free from any glitter elements increasing the definition of the two-tone effect.
The textured vinyl properties of this product type allow coverage of fine surface imperfections and ensure the wall is not cold to the touch. Geo Shimmer Floral Trail Rose Gold / Gold 36874-2 is made in Germany to the highest standards by A.S. Creation Tapeten.
|Made By||AS Creation|
|Adhesive||Powdered Paste Adhesive|
|Application||Paste the Product|
|Dimensions (L x W x H)||1005L x 53W x 0H CM|
Deliveries are made by Royal Mail or Courier (APC, DPD Local, Parcelforce & UPS) depending on the total volume and weight of items ordered. Deliveries should be expected within the hours of 8 am and 7 pm, a signature will be required for all courier dispatched items.
Not going to be at home? Have your order delivered to your business/work address if you do not think an adult will be available to accept and sign for your order.
Orders received over bank holidays or extended breaks will be shipped ASAP following the break, please expect a short delay in delivery. We are open during these times but our couriers and the postal service are not.
Standard Delivery Prices
Sample Delivery (UK & NI) - Free Delivery - Est. 3-5 Working Days
Small Item Delivery (UK Mainland*) - From £5.00 - Est. 3-5 Working Days
Standard Delivery (UK Mainland*) - From £5.00 - Est. 3-5 Working Days
Standard Delivery (Highlands/Islands*) - From £12.50 - Est. 5+ Working Days
Standard Delivery (NI) - £17.50 - Est. 5+ Working Days
Standard Delivery (ROI**) - £20.00 - Est. 5+ Working Days
*Selected postcodes are deemed to be extended or remote areas by our delivery partners, these areas may not get daily deliveries or require additional logistics to complete a delivery. Please enter your address in the checkout to get your actual delivery rate.
If you see an extended delivery charge during checkout and your postcode is not listed in our Full list of exceptions (bottom of page), please contact us.
**Brexit surcharges & duties may be applicable. VAT is payable at the local rate before final delivery can take place.
Express & First Class Delivery
Upgrades are available within the checkout, these are based on postcode area. If they are missing/not visible after entering your delivery address then unfortunately they are not available to your location at present.
We will prioritise any express order and dispatch it the same day (orders before 13:00 on weekdays, subject to stock, excluding weekends and bank holidays) for delivery the following business day^. No dispatch is available on weekends.
^Certain areas are a two business day service, we have no physical control over a parcel once it is handed over to a courier and as such, delivery times cannot be guaranteed.
Premium Service Delivery
Named Day, AM & Weekend services are available to select UK addresses, these services are aligned to the same order processing times and restricted dispatch times/days as noted above).
^^Orders before 13:00 on weekdays, subject to stock, excluding weekends and bank holidays for delivery the following business day^.
No dispatch is available on weekends.
^^^Orders before 13:00 on weekdays, subject to stock, excluding weekends and bank holidays for delivery Saturday or Sunday.
No dispatch is available on weekends.
OUTSIDE THE UK - EU and International
Please contact us stating your full delivery address, the items you would like to order and the quantity of each item. With this information, we can establish a shipping cost for your order requirements. If this is acceptable we will enable orders to your country for 24 hours.
Please note all Non-UK orders payment should be completed via PayPal to ensure authorisation and delivery to the protection address only.
If you are not completely satisfied with your purchase from Home Flair Decor, you may return it within 28 days of ordering. It must be returned undamaged and in its original packaging with all roll labels for a full refund and postage will be at your cost. Please include a copy of your advice note/sales invoice or a note with your Order ID, with all options please include your reason for return.
Please email firstname.lastname@example.org with details of any return before sending goods back.
If a product has been produced individually to your specification then there are no rights to return. This does not affect your statutory rights.
Products should be returned to: Returns Department, Home Flair Decor, Warehouse 1, 679 Eccles New Road, Salford, M50 1AY, United Kingdom.
This address should be used for returns only.
We do not accept returns on wallpaper samples.
Highlands & Islands: UK - Highlands/Islands (Z2)
Isle of Man & Truro: UK - Offshore IOM & TRU (Z3)
Isle of Wight: UK - Offshore IOW (SUR)
Northern Ireland: UK - Northern Ireland
Guernsey: UK - Channel Islands (Guernsey)
Jersey: UK - Channel Islands (Jersey)
Before putting up your new wallpaper, you will need to prepare your walls. This will include, removing old or existing wallpaper, ensuring your walls are smooth, free of cracks or imperfections and are dry. If your walls are freshly plastered or are bare and unpainted they will need sealing (sizing).
Removing old wallpaper ensures that you get the best possible finish. You can remove existing wallpaper in a couple of ways, we would recommend first finding out what type of wallpaper is currently on your wall. If the existing wallpaper peels off easily and almost complete with its backing it is likely that it was a strippable wallpaper or a non-woven (paste the wall wallpaper). In this case you can easily remove all wallpaper then remove any residue with a mild soap solution in hot water.
If your wallpaper is a little more stubborn, then you may have to use a stripping solution or a steam wallpaper stripper. Most wallpapers can be removed by removing the patterned layer leaving a backing layer behind, this is known as peelable wallpaper. Soaking the wall with hot soapy water or a stripping solution, leave for a few minutes to allow the adhesive to soften then gently scraping the wallpaper off with a wallpaper scraper will make easier work of removing this.
For cushion vinyl wallcoverings, often used with tiling on a roll and other kitchen and bathroom wallpapers, scoring of the surface will aid in allowing any steam or stripping solutions to penetrate the surface layer and soften the adhesive layer below, this is known as wet removable. With all stripping, take care to not damage the plaster underneath where possible.
Tip: If you have more stubborn wallpaper, ensure you apply a good amount of soapy water/stripping solution whilst thoroughly wetting the wallpaper..then step away and allow this to work its magic! Repeat this soaking where necessary before you start scraping.
If you take off your wallpaper to find that the walls underneath have a couple of holes or cracks, possibly from old fixtures or fittings, make sure you fill these prior to hanging new wallpaper.
To fill holes in your wall, you can use a multi-purpose powdered filler or a ready mixed all purpose filler and once dry gently sand down with fine sandpaper to ensure a smooth finish.
If you are applying wallpaper to freshly plastered walls you will need to seal them with a wall sealer, also known as wall size or PVA adhesive. Make sure you don’t skip this step as it will greatly increase the efficiency of the wallpaper paste/adhesive by reducing the porosity of the surface. It does also help you with “slip and slide” of the wallpaper as you hang it on the wall, making butting up and pasting in awkward areas that little bit easier.
Another necessary step in preparing to hang wallpaper, is to make sure you have enough rolls to cover your entire room or to complete your project. Our wallpaper calculator can help you work the coverage out. Just remember to allow for around 10-15% extra than you actually need, as you will be trimming excess wallpaper off once it’s on the wall. Feel free to call the team for any help in calculating the number of rolls for you, just have your measurements ready.
Tip: When using wallpaper with a pattern repeat, always allow for extra due to the nature of matching this type of wallpaper you will always end up with a bit more wastage. Feel free to give us a call with your measurements and the pattern details and we can double check your calculations.
Check the roll label symbols for how your wallcovering should be hung. Unless stated otherwise, you can always use the standard hanging technique below.
Paste the wall wallpaper should be hung using a different technique, here is our guide to hanging Non-Woven Paste the wall wallpaper.
Measure the length of the wall using a tape measure and cut enough lengths of paper to complete the first wall, allowing at least 100mm on the length for trimming (50mm at top and 50mm at bottom). Check the pattern match of the wallpaper if using pattern repeat wallpaper and cut your lengths accordingly, you can find more information on using pattern repeat wallpaper in our guide.
Next, using your plumb line and a pencil, softly draw a straight vertical line.
Use a tape measure and extend it into the top corner of the wall you are about to decorate. You should mark the wall at the equivalent width of your wallpaper roll less about 25mm, for a standard roll of 530mm mark the wall 500mm out from the corner.
Repeat holding the plumb line at ceiling height so that it passes through the pencil mark and make several more marks along the line. Join the marks up with the ruler or batten for your convenience in the next steps.
Paste the first length by spreading some wallpaper adhesive the centre of the wallpaper with your paste brush, continue working the brush in a herringbone pattern from the middle out to spread the paste to the edges, adding extra adhesive as needed to give an even layer.
A good technique is to lay the paper against the table edge furthest from you and paste up to this edge first. Then slide the paper towards you and paste the nearest edge. Try to always work cleanly, out from the centre of the length and don't allow paste to get on the front of the wallpaper.
As you are pasting the wallpaper, we recommend folding the wallpaper into concertinas. Ensuring only the pasted side is folded back on itself. Once folded (and correctly pasted) place to one side and leave your wallpaper to “soak”, this usually takes in between 5 and 10 minutes (always check the roll label for confirmation of timings). It is important to let your wallpaper soak until it is pliable,soft and has expanded fully, if you skip or rush this step the wallpaper will likely not adhere to the wall correctly or give you poor results.
Take the length of pasted wallpaper which has been soaked for the correct time and unfold part of the concertina. Lightly press the top against the wall, with a 50mm overlap at the top. Slide the edge up to the vertical line and use a smoothing brush to get rid of air bubbles.
Continue down to the midway point of the wallpaper length, again use herringbone strokes outwards from the centre keeping the edge of the length on the pencil line drawn earlier, you can always double check this is vertical with a spirit level.
Unfold the final concertina, ensuring it is lined up with your pencil line and brushing to remove air bubbles, the bottom of the length should also have a 50mm overlap.
Now trim the top and bottom of the length by creasing the paper into the skirting and ceiling/picture rail with the back of the scissors, then cut along the crease. If using a snap-off blade, ensure this is clean and cut into the crease you’ve made - keeping your fingers out of the way. Should your wallpaper start to snag, snap off an individual section of the blade to renew the tip.
Hang the next length in the same way, butting the edge neatly against the first piece. Make sure the edges are firmly glued down by gently running a seam roller along the joint making sure you do not push adhesive away from the join. Always sponge off any excess paste from the wallpaper, skirting and ceiling with a clean moist sponge/cloth or the paste will dry as a shiny patch.
Check your roll label for any different advice on removal of surface adhesive.
Repeat the process for each length, ensuring that the edges meet exactly and the pattern is matched correctly.
Don't forget to remove any additional adhesive left behind on your ceiling, picture/dado rail and skirting boards. With this final clean tha could you your new wall/s finished! How did it go?
At internal corners, extend your tape measure again and measure from the last length you have hung into the corner, use this measurement and add 15mm to it.
With your next prepared wallpaper length, trim this to the width required from your above measurement. Be careful to cut the excess away from the correct side of the length, this ensures your joins will continue to match up the pattern.
Paste this cut length as before, soak and then when ready offer this to the wall and press the small overlap piece into and back out of the internal corner onto the next wall. You may need to have the full length open without any folds/concertinas to complete this last step.
Now continuing onto the new wall, overlap this section with the next full length of wallpaper, using a plumb line again for accuracy as in step 2.
For external corners, use the same technique but allow about 25mm overlap onto the new wall. Hang the first full length on the new wall so that it is about 12mm from the corner. This will reduce the risk of this lifting.
Once you have completed either type of corner, you can achieve a neat finish by “splicing” a new join. Using a straight edge such as a spirit level and a snap-off blade you can cut through the double layered overlap section, remove both the top surplus and the underlying surplus then smooth down to a neat and tidy new join.
Unfortunately we do not recommend any decorators.
Good Luck from Home Flair Decor.
This product has not been reviewed yet.
Yes we supply A4 samples from £1 each. We also do larger samples from £1.75, these are known as Mill samples (approx 53cm x 53cm). No additional delivery charges are applicable to UK sample orders, European/International sample orders will incur additional delivery charges.
This varies depending on the ventilation in the room and the time of year, usually within the week but has been known to be a few weeks. The wallpaper should be allowed to dry naturally, without any additional heat sources.
The short answer is no. Modern manufacturing techniques mean that wallpapers can be rolled either way. Please ensure that you have checked the direction of the pattern prior to hanging.
Wallpaper is printed on rollers and therefore every wallpaper has a repeat but sometimes on a plain or striped wallpaper the repeat does not matter.
Some common pattern repeats are:
Straight match - The pattern matches across the width of the wallpaper. The label of the wallpaper will tell you how often the pattern repeats eg 64cm.
An offset match or half drop - The match is obtained by halving the repeat. For example a label might state a 53/26.5cm offset match. This means the design repeats every 53cm. The next length/piece to hung on the left or right, will up or down 26.5cm and so forth.
Free match - No matching required. It is the easiest product to hang, as no matter how the strips of wallpaper are hung, no visible join or seams need to be worried about. This also reduces the amount of wastage.
Yes, email us with the batch you require or add a comment within the checkout and we will do our best to help. Contact us at email@example.com
Wallpaper is printed in batches of rolls. It is important to have the same batch number, to ensure colours and pattern match exactly. The batch number is usually located on the wallpaper label close to the pattern number.
Paste the wall wallpaper has additional man made fibres mixed in with the pulp blend that act like a mesh, meaning that paste the wall wallpapers are much stronger than normal and when pasted there is no expansion or shrinkage. Therefore,no soaking time is required before hanging and the paste can be applied directly to the wall instead of the paper creating less mess. However you can still put in on the paper in the traditional way but remember there is no need to soak. Paste the wall wallpaper is also easier to strip when you want to redecorate.
Paste the wall wallpapers require the wall to be of even and solid colour prior to hanging. This is due the man made fibres that create the substrate being translucent and may show any colour variation through the wallpaper.
When using dark coloured wallpapers, it is good decorating practice to darken the ends of your rolls prior to hanging if the manufacturer has not already done this, otherwise you may see the colour of the wallpapers substrate on the joins.
Please use our online wallpaper calculator or download our printable guide here. This will give an estimation based on your measurements. It will not allow for large pattern matches / errors during hanging but will give a good guide.
Wallpaper usually measures 10mts x 52cm or 33' x 20.5''. If different if will be stated.
Using lining paper helps to provide a good base to wallpaper onto, resulting in a much better finish and so we do recommend always using lining paper prior to hanging. Cross lining is also recommended.This is where the lining paper is hung horizontally instead of vertically. This is to avoid the possibility of a wallpaper seam being hung on top of another.